Articles in this section

See more

How to enable TV Connect in D3045?

Updated

TV Connect is a software feature that allows the D 3045 to handle your TV's audio. It enables the D 3045 to learn mute and volume control commands from any TV remote. Additionally, the D 3045 will automatically switch to the OPTICAL source when it detects a digital TV output signal at the OPTICAL 1 or OPTICAL 2 input.*

With TV Connect fully integrated, you can use your TV remote control to manage the following features of the D 3045:

  • Adjust volume up/down
  • Enable or disable the mute function
  • Turn on the D 3045

How to Configure Your D 3045 with TV Connect

To set up TV Connect, connect your TV's digital optical output to the OPTICAL 1 or OPTICAL 2 input of your D 3045. With this configuration, the D 3045 will automatically power up from standby mode and select the OPTICAL 1 or OPTICAL 2 input* when you turn on your TV. You can also wake the D 3045 by pressing the power button on the top panel, the AMP 3 remote control, or your TV's remote control.

*Note: This depends on the D 3045 first entering standby mode after 30 minutes of inactivity.

To integrate TV Connect with your D 3045, follow these steps:

1. Enable Auto Standby Mode

The D 3045 can be configured to automatically enter standby mode if there is no user interaction and no active source input for 30 minutes. Follow these steps to enable auto standby mode.

  • While in standby mode, press and hold the "OFF" button on the AMP 3 remote control for a few seconds until all indicators on the front screen wake up and blink once.

2. Enable Auto Sense Mode

The Auto Sense feature enables the D 3045 to wake up from standby mode when it detects an active source input.

  • While in standby mode, press and hold the SOURCE ˄ button on the AMP 3 remote control until the "049_Standby_button.png" icon on the top screen wakes up and blinks once.

3. Perform IR Learning with TV Remote Control

  • Point the AMP 3 or TV remote control at the D 3045 front screen when performing the procedure below.
STEP** IR Learning Procedure D 3045 Front Display
1 Press and hold [MUTE] of the AMP 3 remote control to initiate IR learning mode.
LEARNING
Choose
One Key

 
2 Press [ON] of the AMP 3 remote control.
LEARNING
POWER
3 Press [ON] of TV remote control
LEARNING
Press
Again
4 Press again [ON] on the TV remote control.
LEARNING
Power OK
Next Key
5 Repeat Steps 2 to 4 to learn “Volume +”, “Volume -”, and “Mute” controls. i. Learning “Vol +”. Press the corresponding remote control button as indicated.
[Vol +] of AMP 3 remote control
LEARNING
VOL +
==> [Vol +] of TV remote control
LEARNING
Press
Again
==> [Vol +] of TV remote control
LEARNING
VOL + OK
Next Key
ii. Learning “Vol -”. Press the corresponding remote control button as indicated.
[Vol -] of AMP 3 remote control
LEARNING
VOL -
==> [Vol -] of TV remote control
LEARNING
Press
Again
==> [Vol -] of TV remote control
LEARNING
VOL - OK
Next Key
iii. Learning “MUTE”. Press the corresponding remote control button as indicated.
[MUTE] of AMP 3 remote control
LEARNING
MUTE
==> [MUTE] of TV remote control
LEARNING
Press
Again
==> [MUTE] of TV remote control
LEARNING
MUTE OK
Next Key
6 Press and hold “MUTE” to stop, complete, or exit the learning mode. Normal operation resumes. Any learned functions before exiting the learning mode are retained and saved.

**Note: Power ON, Vol+, Vol-, and Mute can be learned in any order or sequence.

4. Turn Off the TV's Internal Speakers (If Equipped)

  • It is recommended to disable your TV’s internal speakers so that only the D 3045 outputs sound. This setting is usually found in the TV’s Setup Menu. Refer to your TV’s instruction manual for specific instructions.

Delete IR Learned Commands

  1. Press and hold the [MUTE] button on the D 3045 AMP3 remote control until "LEARNING... Choose One Key" is displayed.
  2. Press and hold [MUTE] again.

Learned IR codes are deleted when the display exits the learning mode screen and returns to the current source.

Related articles